Upload log
From Vorpal Robotics Wiki
Below is a list of the most recent file uploads. See the gallery of new files for a more visual overview.
(newest | oldest) View (newer 50 | older 50) (20 | 50 | 100 | 250 | 500)- 00:54, 29 June 2015 Vorpalwiki (talk | contribs) uploaded File:Fig-12-mimsy-build.jpg (Mimsy Build figure 12. Locking tabs will only align with chassis slots in one way. Make sure you have the right alignment.)
- 00:33, 29 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-11.jpg (Mimsy Build figure 11. Parts needed to join the two drive trains into a single chassis.)
- 23:46, 28 June 2015 Vorpalwiki (talk | contribs) uploaded a new version of File:Mimsy-build-fig-05.jpg
- 23:45, 28 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-05.jpg (Mimsy Build figure 5. Parts needed for servo motor installation.)
- 23:35, 28 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-10.jpg (Mimsy Build figure 10. The two drive trains are now ready to be connected together.)
- 23:31, 28 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-09.jpg (Mimsy Build figure 9. Secure the 20-tooth gear to the servo using a pointed screw. NOTE: do not use the tiny phillips head screwdriver that came with your kit, that's for adjusting the sound sensor and LCD backlight and it's not strong enough.)
- 23:25, 28 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-08.jpg (Mimsy Build figure 8. It's easier to insert the 20-tooth gear with servo horn by holding the drive train with the servo on top. Slide the gear/horn in between the plates and using the large pie-shaped holes on the outer plate, position the gear/horn. Y...)
- 21:57, 28 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-07.jpg (Mimsy Build figure 7. Insert the cross shaped servo horn in the matching slot in the 20-tooth gear. Make sure the collar (in the center) is facing up.)
- 21:40, 28 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-06.jpg (Mimsy build figure 6. Make sure the servo motor's wire is on the opposite side from the notch in the inner plate.)
- 13:58, 27 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-04.jpg (Place the inner plate on the screws (with the inscribed circles face down toward the gears) and use the nuts to secure. Proper tension on the nuts is important. The gears should be able to spin for a couple of seconds if you flick them with your hand. ...)
- 13:39, 27 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-03.jpg
- 13:30, 27 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-02.jpg (Vorpal Mimsy Build Figure 2. Drive train screws placed on outer plate, white spacer and one large spacer placed on each screw.)
- 13:03, 27 June 2015 Vorpalwiki (talk | contribs) uploaded a new version of File:Mimsy-build-fig-01.jpg
- 14:51, 26 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-build-fig-01.jpg (Vorpal Mimsy 1.1 Build Instructions Figure 1, parts needed for drive train.)
- 01:16, 26 June 2015 Vorpalwiki (talk | contribs) uploaded File:Parts-cross-bar-wire-guide.jpg (Cross bar wire guide. This part slots into the cross bar and provides oval windows you can feed motor and sensor cables through, keeping them better managed.)
- 01:14, 26 June 2015 Vorpalwiki (talk | contribs) uploaded File:Parts-cross-bar.jpg (Cross bar. This part mounts under the drive train servos and helps lock the two drive train halves together securely. It also keeps sensor and motor wires from falling down on top of the battery pack.)
- 01:13, 26 June 2015 Vorpalwiki (talk | contribs) uploaded File:Parts-console-wire-plate.jpg (Console wire plate. This is simply used to hold down the LCD and buzzer cables on the console.)
- 01:12, 26 June 2015 Vorpalwiki (talk | contribs) uploaded File:Parts-console.jpg (Console. Provides bezel for LCD display, also the buzzler, Arduino Nano, and IO shield mount on it.)
- 01:10, 26 June 2015 Vorpalwiki (talk | contribs) uploaded File:Parts-front-grill.jpg (Front grill, used to hide wires. Can be removed without tools to change out batteries.)
- 00:57, 26 June 2015 Vorpalwiki (talk | contribs) uploaded File:Parts-outer-plate.jpg (Mimsy 1.1 Outer Plate rev62)
- 02:27, 24 June 2015 Vorpalwiki (talk | contribs) uploaded a new version of File:Mimsy-Arduino-Access.jpg
- 02:24, 24 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-Arduino-Access.jpg (The LCD control panel on the back of Mimsy pops off without tools, allowing access to the microprocessor, IO shield, and electrical system.)
- 02:09, 24 June 2015 Vorpalwiki (talk | contribs) uploaded File:Mimsy-annotated.jpg (Vorpal Mimsy sensors and actuator.)
- 23:40, 23 June 2015 Vorpalwiki (talk | contribs) uploaded File:MainPage-Mimsy11.jpg
- 17:16, 22 June 2015 Vorpalwiki (talk | contribs) uploaded File:Screenshot 20150620-205225 1.png (Vorpal Commander Android App with Drawer Open)
- 17:15, 22 June 2015 Vorpalwiki (talk | contribs) uploaded File:Screenshot 20150620-205243.png (Vorpal Commander Android App in DPAD mode on a small screen device)
- 17:14, 22 June 2015 Vorpalwiki (talk | contribs) uploaded File:Vorpal-commander-tank-drive.jpg (Vorpal Commander Android App in Tank Drive Mode)
- 17:13, 22 June 2015 Vorpalwiki (talk | contribs) uploaded File:Vorpal-commander-arcade.jpg
- 17:10, 22 June 2015 Vorpalwiki (talk | contribs) uploaded File:05-Mimsy-yellow-arm-yellow-sensor-blue-grill.jpg (Vorpal Mimsy with yellow and blue theme)
- 16:59, 22 June 2015 Vorpalwiki (talk | contribs) uploaded File:01-mimsy-all-red-center.jpg (Vorpal Mimsy 1.1 with all red parts down the center of the robot.)