User contributions
From Vorpal Robotics Wiki
(newest | oldest) View (newer 20 | older 20) (20 | 50 | 100 | 250 | 500)
- 23:25, 28 June 2015 (diff | hist) . . (+319) . . N File:Mimsy-build-fig-08.jpg (Mimsy Build figure 8. It's easier to insert the 20-tooth gear with servo horn by holding the drive train with the servo on top. Slide the gear/horn in between the plates and using the large pie-shaped holes on the outer plate, position the gear/horn. Y...) (current)
- 21:57, 28 June 2015 (diff | hist) . . (+150) . . N File:Mimsy-build-fig-07.jpg (Mimsy Build figure 7. Insert the cross shaped servo horn in the matching slot in the 20-tooth gear. Make sure the collar (in the center) is facing up.) (current)
- 21:40, 28 June 2015 (diff | hist) . . (+113) . . N File:Mimsy-build-fig-06.jpg (Mimsy build figure 6. Make sure the servo motor's wire is on the opposite side from the notch in the inner plate.) (current)
- 13:58, 27 June 2015 (diff | hist) . . (+314) . . N File:Mimsy-build-fig-04.jpg (Place the inner plate on the screws (with the inscribed circles face down toward the gears) and use the nuts to secure. Proper tension on the nuts is important. The gears should be able to spin for a couple of seconds if you flick them with your hand. ...) (current)
- 13:39, 27 June 2015 (diff | hist) . . (0) . . N File:Mimsy-build-fig-03.jpg (current)
- 13:30, 27 June 2015 (diff | hist) . . (+126) . . N File:Mimsy-build-fig-02.jpg (Vorpal Mimsy Build Figure 2. Drive train screws placed on outer plate, white spacer and one large spacer placed on each screw.) (current)
- 13:03, 27 June 2015 (diff | hist) . . (0) . . File:Mimsy-build-fig-01.jpg (Vorpalwiki uploaded a new version of "File:Mimsy-build-fig-01.jpg") (current)
- 12:48, 27 June 2015 (diff | hist) . . (+499) . . Vorpal Robotics:About
- 12:17, 27 June 2015 (diff | hist) . . (+2) . . Vorpal Robotics (→Vorpal Mimsy)
- 12:17, 27 June 2015 (diff | hist) . . (+366) . . Vorpal Robotics (→Vorpal Mimsy)
- 14:51, 26 June 2015 (diff | hist) . . (+75) . . N File:Mimsy-build-fig-01.jpg (Vorpal Mimsy 1.1 Build Instructions Figure 1, parts needed for drive train.)
- 12:00, 26 June 2015 (diff | hist) . . (0) . . m Category:Mimsy (Protected "Category:Mimsy" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))) (current)
- 12:00, 26 June 2015 (diff | hist) . . (+393) . . N Category:Mimsy (Created page with "This page lists all pages that pertain to the Vorpal Mimsy Educational Robot. For more specific information, you might look at these narrower category pages: * :Category:Mim...")
- 01:19, 26 June 2015 (diff | hist) . . (+134) . . N Template:Inprogress (Created page with "{| class="wikitable" | '''NOTE: This article is in the process of being created and is currently in an incomplete state.''' |}") (current)
- 01:16, 26 June 2015 (diff | hist) . . (+157) . . N File:Parts-cross-bar-wire-guide.jpg (Cross bar wire guide. This part slots into the cross bar and provides oval windows you can feed motor and sensor cables through, keeping them better managed.) (current)
- 01:14, 26 June 2015 (diff | hist) . . (+200) . . N File:Parts-cross-bar.jpg (Cross bar. This part mounts under the drive train servos and helps lock the two drive train halves together securely. It also keeps sensor and motor wires from falling down on top of the battery pack.) (current)
- 01:13, 26 June 2015 (diff | hist) . . (+94) . . N File:Parts-console-wire-plate.jpg (Console wire plate. This is simply used to hold down the LCD and buzzer cables on the console.) (current)
- 01:12, 26 June 2015 (diff | hist) . . (+99) . . N File:Parts-console.jpg (Console. Provides bezel for LCD display, also the buzzler, Arduino Nano, and IO shield mount on it.) (current)
- 01:10, 26 June 2015 (diff | hist) . . (+86) . . N File:Parts-front-grill.jpg (Front grill, used to hide wires. Can be removed without tools to change out batteries.) (current)
- 00:57, 26 June 2015 (diff | hist) . . (+27) . . N File:Parts-outer-plate.jpg (Mimsy 1.1 Outer Plate rev62) (current)