Vorpal Hexapod Quick Links:
- 1 BILL OF MATERIALS (BOM) FOR VORPAL H12 HEXAPOD
- 2 3D Printing the Plastic Parts
- 3 Building the Robot
- 4 Building the Gamepad
- 5 Assembling Game Accessories and Nameplates
- 5.1 Assembling Sensors
- 5.2 Electrical Connections: Robot
- 5.2.1 NOTES ON JUMPER WIRES
- 5.2.2 NANO PIN CONNECTIONS
- 5.2.3 Bluetooth Module Power
- 5.2.4 Buzzer Power
- 5.2.5 Servo Controller
- 5.2.6 Accessory Port Wire Bundle
- 5.2.7 Connecting the HC-SR04 Ultrasonic Rangefinder to the Accessory Port
- 5.2.8 Connecting the Light Sensor (or any Arduino compatible 5 volt analog sensor)
- 5.2.9 A note on how many things can be connected through the accessory port
- 5.2.10 Robot Screw Sizes
- 5.3 Electrical Connectons: Gamepad
- 5.4 Vorpal The Hexapod Quick Links
BILL OF MATERIALS (BOM) FOR VORPAL H12 HEXAPOD
- These instructions assume you have purchased a kit from us. If you are sourcing your own parts, you need to build the switch/battery connector assembly. For diagrams see Vorpal Combat Hexapod Battery/Switch Construction. Also see important information on that page if you are sourcing your own BEC.
- Full kits of parts as well as individual parts are available on The Vorpal Robotics Store.
- Passive Piezo Buzzer module and 3 wire cable (see image)
- Arduino Nano, 5V, 16 mHz, ATMEGA328 or similar (marked R in our kit to indicate it is pre-loaded with robot software)
- Rotary potentiometer, 10K Ohms, 6mm shaft diameter, with 3 wires pre-soldered. Also, matching dial cap and nut.
- 1 x HC05 BlueTooth Module with 4 x F-F jumper wires for making connections (Note: the HC05 has six pins but only four are used in this project)
- 1 x Servo Controller module (Adafruit 16-channel 12-bit I2C PWM/Servo driver) with F-F jumper wires for making connections, plus 1 two-pin shunt tying V+ to VCC
- 12 x MG90 micro servo motors and associated servo horns (you will only use the single-arm horn).
- 1 x Power distribution wiring with on/off switch, Battery holder for two 18650 cells, 3A 5V BEC, and female connectors to distribute power.
- 3D Printed Parts:
- 1 x Chassis
- 1 x Cap
- 6 x Legs (individually marked with servo numbers)
- 1 x Switch adapter
- 12 x Servo bracket U-shaped halves
- 1 x Electronics Caddy
- 1 x Stand
- 1 x Eye/glasses Decoration
- 1 x Joust game accessory with "rider"
- 1 x Capture the Flag game accessory with flag and cup.
- 1 x Fidget Spinner Challenge game accessory (no Fidget Spinner, just the stand)
- 1 x Ultrasonic Rangefinder Bracket
- 20 x 10mm diameter ceramic magnet, north pole marked. 6 are for robot top, 1 for eye/glasses decoration, 7 for Capture-the-Flag and Joust accessories, 6 for Kung Fu accessory.
- 12 x socket head cap screw, 2.5mm diameter by 8mm long
- 5 x #6-32 x 1/2" screw to fasten on/off switch adapter (2) and to hold electronics caddy on chassis (3)
- 1 x L shaped hex driver for both kinds of screw
- 1 x Battery/Switch Wiring Unit with 9v battery clip. (Note: the gamepad requires no BEC so you can use this fact to distinguish from the robot wiring unit)
- 1 x button matrix with associated connecting wires
- 1 x Dpad Button module with associated connecting wires
- 1 x HC05 Bluetooth module and four wires to connect it
- 1 x microSD Card Reader module and six wires to connect it. NOTE: A microSD card, not included in the kit, is required for record/play features to work. The capacity should be 1gb or less. Strongly recommend FAT file system and 512 byte allocation unit size (use FORMAT on your computer to reformat if necessary).
- 1 x Ardunio Nano, 5V, 16 mHz, ATMEGA328 or similar (marked "G" in our kit to indicate it is pre-loaded with Gamepad software)
- 3D Printed Plastic Parts:
- 1 x Gamepad base plastic part
- 1 x Gamepad top plastic part
- 1 x Gamepad button carrier
- 1 x Switch Adapter
- 6 x #6-32 x 1/2" screw to hold cover on gamepad (4) and also to hold switch adapter on base (2)
3D Printing the Plastic Parts
This project has been finely tuned to make it easy to 3D print. No supports are required for any of the parts. In some cases you may want to use brims or rafts to help parts adhere to the print surface. There is minimal bridging, never farther than about 15mm (5/8"). Some of the parts do require some flexibility, for example the sides of the servo compartments need to bend outward while the servos are inserted, they then snap back into place when the servo is completely inserted. This means brittle plastics like PLA are not the best choice for this project. (Although we have made PLA hexapods and they do work if you're careful when inserting the servos).
This page assumes you have basic familiarity with 3D printing and 3D printing terminology. If not, you might want to reference online materials such as youtube videos or information from your 3D printer manufacturer before attempting this project.
If you are 3D printing the plastic parts (as opposed to buying them pre-printed), here are some tips.
- MINIMUM PRINTER REQUIREMENTS
- The bed size should be at least 150mm cube (5.9 inches cube). The largest part is the hexapod base so it is the limiting factor on bed size.
- A heated bed is strongly recommended, especially if you are printing in ABS.
- RECOMMENDED PLASTICS
- ABS and PETG both work well. When we sell Full Kits and Assembled Vorpals we use ABS.
- PLA is somewhat brittle, but it will work if you're careful. Inserting the servos into the legs and hips will somewhat flex the plastic so be careful during that process with PLA.
- PRINT SETTINGS. We print using the following settings on a Lulzbot TAZ 6 or Lulzbot Mini with 0.5mm nozzle:
- 0.38 layer thickness (or whatever layer thickness is optimal for your printer)
- 1mm walls (i.e. two perimeters)
- 1.14mm top and bottom (i.e. three layers)
- 15% infill
- You can print with thinner layers if your printer does not support 0.38mm layers or if you want a more refined look, it will just take longer.
- BRIMS AND RAFTS
- Brims or rafts are recommended for the following hexapod parts: Base, Legs, Electronics Caddy, Cap. This ensures proper bed retention to avoid warping. These parts have relatively little contact area with the print bed, or have certain sections with little contact.
- Brims/rafts are not recommended on any of the other parts. The other parts generally have enough bed surface contact that they will print fine without brims. Your mileage may vary however and it is recommended that you keep a close eye on the first few layers of the print to make sure everything is sticking properly. If not, you can cancel the job with minimal loss of plastic then restart with brims or rafts.
- We personally prefer brims (such as available in Cura) as they are easy to remove and leave a clean look.
- POST PRINT
- Other than removing brims/rafts and the occassional drip, there is not any special post-processing required after printing.
- However, be very careful to inspect the hemispheres jutting out of one side of each of the servo holders, these need to be as low friction as possible. Inspect for drips and defects. If necessary, use a file or sand paper to smooth them out.
- OBTAINING THE STL FILES
- We have posted the STL files to many popular 3D printing model sites such as http://www.thingiverse.com.
- Please note: These parts are considered in pre-release status at this time. Our official release date is currently projected to be October 20. The parts we are posting have been printed many times and tested and do work well for us, but we are making a few more tiny adjustments and refinements.
- Please help us by rating the VCH project (or clicking on the LIKE button or equivalent) on whichever site you download it from!
Building the Robot
You will need the following tools:
- 2mm hex key. A 5/64 inch hex key will also work. This is in the Hexapod Parts bag. (NOTE: Some very early kits put this in the Deluxe Parts Bag).
- A marker that can write on dark plastic and still be seen, such as Sharpie Metallic or Sharpie Oil markers (white and yellow work great).
- This is the easiest way to mark servo wires with their corresponding leg number
- If you don't have these types of marker, you could use clear tape and bits of paper to tape wire labels near the socket end of the servo cable. Don't put labels right on the black plastic connectors at the end of the servo because you'll make them too thick to fit side by side when plugged in.
Servo Pre Check
Sometimes the servo motor gearbox will get locked up when sitting for a long time, for example during shipping, especially in cold weather. The following procedure will ensure they work properly. (Note: Some MG90S servo bags distributed in the past with our kits say not to turn the servo horn, these instructions supercede that note on the bag).
- Put a one-arm servo horn on each servo. You don't need a screw, just put it on in any random position for now.
- Slowly and gently rock the servo horn by hand so it turns. Do not use a lot of force. Note that there is a physical stop that only allows it to turn 180 degrees. If you push in one direction and it won't move, rock it in the other direction.
- As soon as it moves, even just 10 or 20 degrees in either direction, you've confirmed the servo is not locked. Do not leave it at an extreme position where it stops, leave it somewhere around the middle.
If any servo fails to move with modest pressure and a gentle rocking motion, put a mark on that servo, near where the wire comes out. It will most likely unfreeze when power is applied, but you need to keep an eye on it for now.
Step by Step Instructions
- STEP 1: Insert accessory port screws in the chassis Insert 5/8" #6-32 hex head screws in the bottom two holes of the accessory port, head of the screw inside the hexapod, then tighten nuts outside. Repeat for the top two accessory holes with shorter 1/2" #6-32 hex head screws. The heads of the screws recess into hexogonal holes so you don't need to use pliers inside the robot body, just for the nuts. Two wingnuts go on the two lower screws, these will be used to secure accessories such as the Joust lance or Capture-the-Flag attachment.
- STEP 2: Insert servos in the chassis.
- Next, insert the servo into the chassis as shown in the diagrams below. As you insert the servo into the chassis, slowly press it straight into place until it clicks in under the small tab on one side of the servo holder. Make sure it stays straight as you push down.
- Immediately mark the black connector at the end of the wire to indicate the servo number (which is engraved in the top of the servo holder, a number between 0 and 5).
- A metallic sharpie pen works very well for this, or a light colored oil paint sharpie such as white.
- If you don't have any of those things, a little piece of masking tape can be affixed to the wire and marked, or you could use clear cellophane tape to attach little bits of marked paper to the wire. Do not attach any tape or paper to the black connector, as it will be a tight fit when connecting later.
- The wire coming out of the servo sticks out away from the robot, the servo shaft would face down toward the table top if the chassis were resting on the table.
- After inserting the servo, thread the wire through the top servo wire guide hole, and into the center of the chassis.
- STEP 3: Insert the servos in the Legs. The technique is very similar to inserting the servo into the chassis.
- Insert the servo straight into the leg socket so that the wire is coming out of the servo facing away from the plastic leg and the face of the servo with the shaft and servo horn goes into the open faced side of the leg, as shown in the diagram.
- The servos in the legs are called the "knee" servos. Each leg has a higher number on it, this is the knee number, they run from 6 to 11. Again, write this number on the black connector at the end of the servo wire. PRO TIP: For 6 and 9, underline the number so you don't read them upside down!
- STEP 4: Thread each leg servo wire into the bottom wire guide slot on the chassis. Each leg servo should be matched with a hip servo plus 6. The legs are marked with the hip number near the top and the knee number below that. For example, the leg marked 6 should be threaded through the wire guide on hip servo 0, leg 7 goes with hip 1, leg 8 goes with hip 2, etc. Add 6 to the hip number to get the leg number.
- STEP 5: Build the electrical system., You need to power up the servos and make them seek to the 90 degree position, this will allow you to adjust the legs properly for walking.
- STEP 5A: Take the potentiometer and remove the cap, then unscrew the nut and set these items aside for now. Push the potentiometer shaft from the inside of the chassis, into the hole that has the markings "STOP", "TST", etc. The wires coming out of the potentiometer should be pointing down and you may need to bend them a bit to make it all fit. Put the retaining nut on the potentiometer, hand tighten first and then give it just another half turn or so with pliers if desired. Turn the knob all the way counter clockwise, then insert the knob so it points to the letter "O" in the word "STOP".
- STEP 5B: Take the on/off switch (which is attached to the battery holder assembly) and thread the switch wires through the gap in the switch adapter. Insert the switch and adapter into the switch hole from the inside of the chassis, lining up the holes of the switch adapter with the two matching holes in the chassis. Insert a #6-32 1/2" screw from the outside and turn it to secure one side of the switch, repeat for the other hole. You should put a finger over the hole from the inside of the chassis and apply pressure while screwing in the screw. (See diagrams below.)
- STEP 5C: Make the connections listed in the ELECTRICAL CONNECTIONS section of these instructions below. Be extremely careful about the power connections. Double check all connections before powering on.
- STEP 6: Power up! Make sure the on/off switch is off, and the knob is turned to STOP. Insert batteries and power on the robot using the on/off switch. You should hear a beep, a pause, then a second beep. The servos should all twitch into position. If the robot does not move at all, immediately turn the switch off and check your connections again. If some of the servos don't move (especially any you marked during the servo pre-check) then gently push them with power off to see if you can free them up. If they still won't move, try pushing them with power applied, but turn off the power within 30 seconds if they're locked up. If you can't get the servo to move it will need to be replaced.
- STEP 7: Insert Servo Horns. The servo horns are all at random angles right now due to the servo pre-check. In this step we'll make them point in the right direction. The knee servos are not at 90 degrees when the knob is all the way counter clockwise, rather they are at a 30 degree standing angle. We need to get them to 90 degrees so its easy to align the servo horn. Turn the knob very slightly clockwise and you will see all the knee servos twitch. This is "adjust servo horn mode". All servos (knees and hips) are now at their halfway point, 90 degrees. Now you need to take each single arm servo horn and carefully insert it on the shaft so that it is sticking straight out as shown in the figure. You will not always be able to make the horn come totally straight out. This is because there are only 22 little groves (splines) in each shaft, meaning you can in general only come within about 8 degrees of being at a perfect 90 degree angle. This amount of error is acceptable, just get it as close as you can. It is better for the horn to be a little too much clockwise than to be a little too much counterclockwise, especially for the knees. Do this for all hip and knee servos. Do not insert any screws yet.
- STEP 8: Assemble the leg hinges. Each leg hinge is composed of two identical U-shaped parts. Take one in each hand and align the two so that the bump (shown in the diagram at the right) are both near each other. Turn one 90 degrees with respect to the other.
- Gently squeeze each piece between thumb and forefinger, which causes the little jaws in the center to open up slightly. Work the two halves together. Squeeze just enough so they work their way on, no more or you might break the part!.
- At this stage, you may notice that the parts are loosely clamped on each other. Don't worry! When you place the leg hinges over a servo, the servo will spread it apart and they will lock together tightly.
- STEP 9: Attach Leg Hinges. The leg hinges connect the hips to the knees. They only go on one way. First place the end that matches the servo horn on, then you need to very slightly bend the U shaped piece while pulling it over the hemispherical bearing on the other side. It's a little easier to do the knees (servos mounted to legs) first, followed by the hips (servos on base).
- NOTE: It should not be excessively difficult to push the hinge over the hemispherical bearing. If you find you are struggling, that means the hinges are too tight. This may affect walking. This can be due to the kind of plastic you used or how your printer is adjusted. You may need to gently spread the two legs of the U shape by hand before putting the hinge on the robot. Be careful of course not to break the hinge.
- STEP 10: Test Knee Positions. Turn the knob fully counter clockwise (to STOP) and the robot will go into "stand still" mode. Place it on a level surface such as a table top. Do all of the legs touch the ground? If one or more legs don't touch the ground, you need to adjust the servo horn on the knee a little bit so it does touch. Gently pull off the servo bracket. Pull the servo horn off, and put it back on just a little bit moved so the leg would move closer to the ground. Put the servo bracket back on, and see how it looks. Do this until all legs are at least slightly touching the ground. Again, you can't necessarily be perfect due to the 8 degree increments the servo horns can be moved. But you should be able to be close enough that all legs at least slightly touch the ground.
- STEP 11: Insert Servo Screws. Now that the legs are adjusted, you can insert the M2.5x8 screws into the servo horns to lock them in place. Note that you will NOT be using the screws that were in the little bag the servos came in, you'll be using the separate pack of screws, which are longer than the ones in the servo bag. Do not overtighten these screws, as you could possibly crack the servo brackets. Just turn the screws until you start to feel resistance, then turn a quarter turn more and stop.
- STEP 12: Test Individual Servos. To test whether every servo is working, put the robot on its stand. Then start with the knob on STOP, then slowly turn it clockwise. First the servos will go into adjust mode, you used that a moment ago to set the servo horns. But, keep going, and the robot will go into "individual servo test mode". In this mode, every hip servo will move, one by one. When all the hips have moved, every leg will move, one by one. You should see every servo move, in order. If some don't move, check your connections. A common error is to plug a servo connector into the servo controller backwards (i.e. the brown wire is matched with the yellow pin instead of the black pin).
- STEP 13: Test Using Demo Mode. Ok, everything looks good, so time for a full test. Turn the knob to STOP, then take the robot off the stand and put it on the floor. Turn the knob to DEMO, and the robot will go through a series of movements to demonstrate some of the things it can do. The full demo only takes about 30 seconds, then repeats. Here, you are looking for the robot to, for example, be able to get back up off the floor after doing some of its dance moves. If the robot struggles to get off the floor, you may have a battery that is not fully charged, or there may be too much friction between the servo bracket and the little ball socket it sits in. A tiny bit of silicone lubricant will usually fix that problem, or just make sure those parts are cleaned up from 3D printing and don't have an excess strands of material that are causing friction. See the Trouble Shooting Guide for more information about different kinds of issues that can occur.
- STEP 14: Store the Electronics in the Caddy Now things look pretty messy with all those wires hanging loose, let's clean it up by stowing them in the electronics caddy. Please reference the video and diagrams here for quick instructions.
- STEP 14A: Insert Caddy Bars Insert the two electronics caddy bars as shown in the diagrams below. Notice carefully how they are inserted. You may need to slightly squeeze the forked section at the end to work it into the hole. Once inside, it may be difficult to remove because it will snap into place, so be sure you're putting it in the right way.
- STEP 14B: Insert the Servo Controller and Arduino Nano The diagrams here do not show the wires to make them easier to visualize. Carefully insert the servo controller as shown, making sure you don't pull out any of the wires. You may need to wiggle the electronics caddy bar from side to side a bit so that components can slide past it during insertion. Notice that the end of the Servo controller with wires sticking out of it must go in last. Carefully insert the Arduino Nano as shown, making sure you don't pull out any of the wires. You may need to wiggle the electronics caddy bar from side to side a bit so that components can slide past it during insertion. Notice that the end of the Nano that has the USB port must go in last.
- STEP 14C: Insert the HC05 Bluetooth Module The diagrams here do not show the wires to make them easier to visualize. The HC05 Bluetooth module with a name beginning with "S" should be used for the robot. For example, the label will read something like "VORP S2944" (the number will differ). The one marked "M" will be used for the gamepad. Slide the HC05 into the side drawer as shown. When inserting, be careful not to pull out the wires, which will be a little tight. Work the wires into the little space provided so they stay clear of the robot's cap when it gets screwed on later.
- STEP 15: Assemble the Cap
- STEP 15A: Put magnets in the Cap Insert a magnet in each magnet holder in the cap. The magnets are marked with a dimple on the North pole side. It is important that this dimple be showing after installation. In other words, insert the magnet with the non-dimple side down. Pressing with just your fingers might work, but if the magnet does not complete seat, use pliers to gently squeeze it into place. Be careful because if you squeeze too hard you might crack the Cap.
- STEP 15B: Decorate If desired, use a permanent marker to color the Vorpal "V" on top of the Cap. Oil markers work well. On light colors of plastic a black permanent marker will also work.
- STEP 15C: Put Cap on the Hexapod Screw the cap on the robot by lining up the tabs with the matching slots in the rim of the base. Turn the cap clockwise to lock it in place. IMPORTANT: Do not press down on the robot to insert the cap when the robot is under power standing on its legs! You can damage the leg motors by doing this. It is best to turn the robot off, and either support the bottom of the Base with one hand and press the Cap on with the other, or set the Base down on the table top or floor with legs out to the sides so they don't take pressure.
- STEP 16: Warning Label There are two a self-stick choking hazard warning labels in the hexapod parts bag. Peel the backing off one of them and place it on the bottom of the robot, near the center. Retain the second label for the gamepad.
Building the Gamepad
To go beyond demo mode, you need to build the Vorpal Gamepad. The Vorpal Gamepad allows you to call up many different actions by the hexapod such as walking, turning, dancing, or fighting. The gamepad can also be used as a transmitter to allow Scratch programs to wirelessly control your robot from a computer.
- STEP 1: Attach cables to the button matrix. Pull 8 wires off the Dupont wire bundle. The colors don't really matter so just take 8 adjacent wires and leave them together if possible. Carefully push these 8 wires, in order, onto the pins coming out of the 4x4 button matrix. Make sure the wire connectors don't "swap places" by twisting under each other, it is very important that the order be correct.
- STEP 2: Attach cables to the yellow DPAD buttons. Pull three wires off the Dupont wire bundle of the following colors: red, black, white. Plug the white wire into the yellow DPAD button module's pin marked OUT (output). The middle pin marked VCC gets the red wire, and the pin marked GND gets the black wire.
- STEP 3: Install the switch. Take the switch/battery assembly and use two #6-32 screws 1/2" long to attach it on the inside wall of the gamepad base, in the rectangular hole. The switch itself is sandwiched between the gamepad wall and a switch adapter (the same switch adapter model used for the robot is used for the gamepad, you need to print two of them). DO NOT OVER TIGHTEN THE SCREWS.
- STEP 4: Place the buttons Place the 4x4 button matrix and also the yellow DPAD button module in the matching places on the button bracket. The yellow DPAD buttons should be placed down first, and you may need to slightly bend the pins downward. The 4x4 button matrix also should have its pins slightly bent downward, then its wires will go on top of the wires coming out of the yellow DPAD button module.
- NOTE: The yellow caps on the DPAD buttons are optional. We normally remove these because we have found that in demo situations some people, especially young children, will press the yellow buttons so hard that they dislodge the caps. They will press right back on, it's not a problem really, however they may think they broke the controller. We feel it's better just to take them off.
- STEP 5: Connect the electrical system wires. Using the connections indicated in the section below on electrical wiring, plug in all the wires for the Arduino Nano and HC05 Bluetooth module.
- STEP 6: Insert the Arduino Nano. The Arduino Nano should be oriented such that its USB port is coming out the square hole on the left side of the base, and all the outgoing wires from the Nano are coming out toward the front of the base. Once in place, gently push the side of the Nano opposite of the USB port until it clicks into place, securing it.
- STEP 7: Insert the HC05 Bluetooth Module. Slip the HC05 Bluetooth module under the U shaped bracket near the center of the gamepad base. Its lights should be facing upward, they will be visible through holes in the top of the gamepad and this helps you know that the gamepad is turned on.
- STEP 8: Put it all together. Put the 9v battery clip inside the battery box area of the base. Place the button bracket on top of the base, then place the gamepad top on the button bracket, sandwiching the button modules in place. Align the four screw holes in the corners with the matching holes on the base and secure with four #6-32 screws 1/2" long. DO NOT OVER TIGHTEN. NOTE: You might want to just put two screws in, and don't even put them all the way in, until you test the gamepad. In that way, if it does not work, you can easily open it back up to check connections.
- STEP 8: Test! Turn the switch to "0" (off). Connect a 9v battery to the 9v battery clip then slide the battery door onto the base. Turn the switch to "1" (on). Lights should be visible through the holes. Turn the hexapod's dial all the way clockwise, to "RC" thus putting it in Bluetooth mode. Turn the hexapod on and wait a few seconds for it to completely boot. Try to control the robot! Try hitting each of the top three rows of 4x4 matrix buttons (W, F, D) one by one, and test to make sure every mode functions. If most modes work but a couple do not, you may have swapped some wires coming off the matrix.
- STEP 9: Decorate If desired, use a marker to darken the Vorpal "V" symbol, the W, F, D, R markings, the 0 and 1 switch markings, and the record/play symbols under the 4x4 button matrix. This will make them more visible as well as making the gamepad look nicer. We like using oil based paint markers. For dark colored plastics, use a white oil paint marker, for light colored plastics use black, blue, or red to contrast with the plastic color.
STEP 10: Warning Label There were two a self-stick choking hazard warning labels in the hexapod parts bag. You used one for the robot. Peel the backing off the other and place it on the bottom of the gamepad, being sure not to interfere with the battery drawer.
Assembling Game Accessories and Nameplates
Most of the accessory pieces require no assembly, or just require press fitting magnets into round holes.
When inserting magnets, the rule is: anything that attaches to the robot via the accessory port screws should have the dimpled side of the magnet showing, and anything that is supposed to attach to the robot or a screwed-on accessory should have the dimple side down, not showing.
Based on this rule, the dimpled side of the magnet should not show for these items:
- Joust Rider
- Name plate
And the dimple should be showing for these items:
- Capture the Flag Arm
- Joust Lance
The light sensor and ultrasonic rangefinder sensor can be assembled with two screws each. The sensor module is sandwiched in between two plastic pieces. These screws are in the Deluxe Parts Bag. The screws will self-thread into the plastic. Do not overtighten or you will strip the plastic and the screws won't hold. When the screw head is all the way down, stop turning.
The ultrasonic rangefinder sensor attaches to the accessory port screws.
The light sensor wedges into one of the slotted holes in the cap.
Electrical Connections: Robot
NOTE: These are the official RELEASE 1 connections. If you have an older prototype (you can tell because the gamepad has no SD card reader in the older version) then please see Vorpal Combat Hexapod Prototype Electrical Connections.
NOTES ON JUMPER WIRES
There are two different lengths of female-female Dupont jumper wires used to make most connections. The longer ones (20cm) are only used for the Hexapod's accessory port connections. The shorter ones are used for all the connections on the Gamepad and all the connections on the Hexapod between the Arduino Nano, Servo controller and Bluetooth module.
Wire Color Conventions
Please follow these conventions when selecting wire colors:
- For +5V, Vin, and similar positive voltage connections, use either RED or ORANGE.
- For GND and other negative electrical connections, use BLACK or BROWN.
- For the connectors that sit at the mouth of the accessory port (used for optional sensors) colors are suggested below in the instructions. By following these suggestions you will make your life easier when connecting sensors!
- For all other connections, you can use any color you want, it's arbitrary.
If Jumper Wires Are Too Loose
Sometimes you will find a wire whose connector does not grip the pin well enough. It might fall off very easily or just by gravity alone. If that happens, you have a few options:
- There are extra wires in your kit. If you find a wire that's too loose, just use a different wire.
- Using the hex key, you can put the jumper housing on a flat surface then press on the metal showing through the plastic connector, which will tighten up the jumper wire's grip. Don't go too overboard on pressing though or you might make it too hard to insert.
- Alternatively, you could use electrical tape after inserting all the wires on a module (such as the Nano) to effectively attach together all the little plastic female connector housings. In that way, the connectors that do grip will help hold in the ones that are too loose. Some people also like using hot glue for this purpose. (Personally, I don't like using hot glue, as it makes it harder to change connections if you hooked something up incorrectly.)
NANO PIN CONNECTIONS
- Digital IO Pins:
- D0, D1 are reserved because they are used for uploading programs to the robot, so nothing will be connected there.
- D2 Bluetooth Module Rx
- D3 Bluetooth Module Tx
- D4 Buzzer Signal (white wire)
- D5, D6 NO CONNECTION. These pins are reserved for future expansion.
- D7 20cm GREEN Dupont connector routed to accessory port, used for Ultrasonic Rangefinder TRIG
- D8 20cm BLUE Dupont connector routed to accessory port, used for Ultrasonic Rangefinder ECHO
- D9 No connection. This pin is reserved for future expansion.
- D10 through D13 are reserved for the optional CMUCAM5 (Pixie) sensor accessory.
- Analog Pins:
- A0 Potentiometer signal (white wire)
- A1 Potentiometer Power (red wire)
- A2 Potentiometer Ground (black wire)
- A3 20cm YELLOW Dupont connector routed to the accessory port, for the optional light sensor or other analog sensors.
- A4 Servo Controller SDA
- A5 Servo Controller SCL
- A6 20cm PURPLE Dupont connector, routed to the accessory port, for any analog sensor you wish to optionally add later.
- A7 No connection, reserved for future use.
- Power Pins:
- VIN pin on Nano connects to Battery positive (the red Dupont connector coming off near the switch on the wiring module)
- GND pin on Nano connects to Battery negative (the black Dupont connector coming off the battery black wire)
- Second GND pin on Nano (there are two GND pins on the Nano) connects to the GND pin on the HC05 module
- +5V on Nano connects to HC05 +5V Pin
IMPORTANT NOTE: The red Dupont connector coming off the switch/battery assembly must go to VIN and never +5V, because the battery voltage is much higher than +5 volts. You will more or less instantly destroy your Nano if you put unregulated battery power directly into the +5V pin. The VIN pin has its own voltage regulator. The +5V pin on the Nano will be used to provide regulated power to the Bluetooth module.
Bluetooth Module Power
- +5V on HC05 connects to Nano +5V pin
- GND on HC05 connects to either of the two Nano GND pins
- Connect the buzzer V+ and ground (marked "-") pins (red and black respectively) to Port 13 of the Servo Controller, matching black and red wires to black and red pins on the Servo Controller. You will be using the special three wire cable provided for this purpose. It has a three-pin connector one one side, and the other side has a two-pin connector and a one-pin connector. The one-pin connector goes to the Nano and provides the signal to drive the buzzer. The two-pin connector is plugged into Servo Controller Port 13.
- Connect the 12 servos to port numbers corresponding to the servo marking (0 to 11). Make sure the signal wire (yellow) is oriented correctly and matches the yellow plastic header pin.
- Connect the switch/battery module regulated BEC output (a three pin Dupont connector where only two of the pins are populated, one with a red V+ wire, one with a black ground wire) to servo controller port 12 power and ground. Make sure the RED wire is going to VCC (red pin) and the BLACK wire goes to GND (black pin).
- On one short side of the Servo Controller you will find a VCC and V+ pin right next to each other. Use a shunt (small black connector that goes over two pins) to connect those together if one is not already installed. This shunt causes both the servos and the microprocessor to run at the same +5V level.
- SDA and SCL go to A4 and A5 on the Nano, respectively.
- Servo port 12 RED and BLACK pins are connected to the output of the BEC. Make sure the BEC RED wire matches with the RED pin, and the BEC BALCK wire matches with the BLACK pin.
- Servo port 13 RED and BLACK pins are connected to the passive buzzer power connector. Make sure the buzzer BLACK wire matches the BLACK pin, and the RED wire matches the RED pin.
- Servo port 14 RED pin goes to a 20cm ORANGE Dupont connector and is routed to the accessory port to provide +5V for sensors or other accessories.
- Servo port 14 BLACK pin goes to a 20cm BROWN Dupont connector and is routed to the accessory port to provide GND for sensors or other accessories.
- Servo port 15 RED terminal goes to a 20cm RED Dupont connector and is routed to the accessory port to provide +5V for sensors or other accessories.
- Servo port 15 BLACK terminal goes to 20cm BLACK Dupont connector and is routed to the accessory port to provide ground for sensors or other accessories.
- Servo port 15 signal terminal goes to 20cm WHITE Dupont connector and is routed to the accessory port to provide signal for a servo used in an optional accessory.
Accessory Port Wire Bundle
The 20cm wires connected to the Nano and Servo Controller provide access to digital ports, analog ports, and power for accessories such as sensors, lights, or other projects. These wires should be bundled up near their unconnected ends (a rubber band works well for keeping them all together) and routed to the large opening below the accessory port hex head screws on the chassis. When there is no accessory in use, these wires can remain tucked inside the accessory port. When needed, pull them out a few inches and connect to sensors or other electrical accessories.
Connecting the HC-SR04 Ultrasonic Rangefinder to the Accessory Port
When building the robot you routed longer jumper wires (20cm) to the accessory port. You need four of these wires to use the Ultrasonic Rangefinder:
- RED accessory port wire goes to HC-SR04 VCC
- BLACK accessory port wire goes to HC-SR04 GND
- GREEN accessor port wire goes to HC-SR04 TRIG
- BLUE accessory port wire goes to HC-SR04 ECHO
Connecting the Light Sensor (or any Arduino compatible 5 volt analog sensor)
- RED or ORANGE accessory port wire goes to Vcc (may also be marked +5V or Vin) on the sensor
- BLACK or BROWN accessory port wire goes to GND on the sensor
- YELLOW (A3) accessory port wire goes to the Signal pin on the sensor. This may be marked different things on different sensors.
- You may also use PURPLE (A6) for a sensor (or a second sensor)
- The Scratch Sensor block allows you to choose A3 or A6 sensor ports.
A note on how many things can be connected through the accessory port
We are providing two sets of power connectors at the accessory port for sensors or other accessories. RED/BLACK and ORANGE/BROWN each respectively provide +5V/GND. It's up to you what things you want to connect using these. You could have one or two sensors, you could have a sensor and some kind off motorized accessory. You could have a sensor and an LED light strip, etc.
Nothing is stopping you from creating a Y connector to make additional power connections, except that there is a limit of 3 amps of current that you can pull from the battery/BEC system. The robot itself needs up to 2.5 amps during fast motions. But many sensors can operate on just a few milliamps. Adding a motorized accessory is where you would need to be careful about how much current you're pulling from the system. If you pull too much current, typically the BEC will overheat and go into thermal protection mode, which will shut down all the motors until you reboot the robot. It is possible to use a mini servo under moderate load for a motorized accessory, but a full sized servo under heavy load might be too much. Use caution when designing your own accessories, especially if they are going to use more than a few hundred milliamps of current.
Robot Screw Sizes
- Servo horn screws: 12 x M2.5 by 8mm long
- Switch assembly: 2 x #6-32 by 1/2" long
Electrical Connectons: Gamepad
Note: These connections are for the Kickstarter Release 1 product. If you have an older prototype (the gamepad does not have an SD card reader in the prototype) then please see Vorpal Combat Hexapod Prototype Electrical Connections.
GAMEPAD NANO PIN CONNECTIONS
- D2 through D9 are connected to the button matrix pins.Looking from the top of the button matrix module, the rightmost button matrix pin (labeled 1) goes to D9, second to right (labeled 2) to D8, etc.
- D10 to SD card CS (may be labelled SS on some SD card readers)
- D11 to SD card MOSI
- D12 to SD card MISO
- D13 to SD card SCK (may be labelled SCL on some SD card readers)
- A0 Unused
- A1 Dpad OUT (white wire)
- A2 Dpad VCC (red wire)
- A3 Dpad GND (black wire)
- A4 HC05 Bluetooth Module Rx
- A5 HC05 Bluetooth Module Tx
- A6, A7 Unused
- VIN battery/switch positive (red wire)
- GND Either ground on the Nano goes to the battery/switch negative (black wire)
- ICSP pin 4 (see diagram): SD card reader GND
- ICSP pin 6 (see diagram): SD card reader VCC
- Nano +5V pin goes to HC05 +5V pin
- Nano GND pin (there are two, you can use either one) goes to HCO5 GND pin
GAMEPAD: Screw Sizes
- Switch assembly, 2 x #6-32 by 1/2" long
- Gamepad Cover, 4 x #6-32 by 1/2" long
Vorpal The Hexapod Quick Links
|Sign Up For Our NEWSLETTER||VORPAL FORUM: Join the Discussion|
Getting & Giving Vorpal