File list
From Vorpal Robotics Wiki
This special page shows all uploaded files.
| Date | Name | Thumbnail | Size | Description | Versions |
|---|---|---|---|---|---|
| 01:31, 29 June 2015 | Mimsy-build-fig-15.jpg (file) |  |
981 KB | Mimsy Build figure 15. Insert the cross bar with the two square holes facing the side of the servos that have the wires. You need to angle it in. Just loosely put both sides in the slots, don't force it forward to lock yet. | 1 |
| 01:10, 29 June 2015 | Mimsy-build-fig-14.jpg (file) |  |
1.08 MB | Mimsy Build figure 14. Front and rear floors installed on one drive train. | 1 |
| 01:06, 29 June 2015 | Mimsy-build-fig-13.jpg (file) |  |
190 KB | Mimsy Build figure 13. Make sure the locking tabs are pushed all the way through the slots so they are firmly connected. | 1 |
| 01:00, 29 June 2015 | Mimsy-build-fig-12.jpg (file) |  |
793 KB | Mimsy Build figure 12. The locking tabs will only align one way with the slots in a drive train. Make sure you have the right match-up. | 1 |
| 00:33, 29 June 2015 | Mimsy-build-fig-11.jpg (file) |  |
709 KB | Mimsy Build figure 11. Parts needed to join the two drive trains into a single chassis. | 1 |
| 23:46, 28 June 2015 | Mimsy-build-fig-05.jpg (file) |  |
183 KB | 2 | |
| 23:35, 28 June 2015 | Mimsy-build-fig-10.jpg (file) |  |
1.2 MB | Mimsy Build figure 10. The two drive trains are now ready to be connected together. | 1 |
| 23:31, 28 June 2015 | Mimsy-build-fig-09.jpg (file) |  |
1.59 MB | Mimsy Build figure 9. Secure the 20-tooth gear to the servo using a pointed screw. NOTE: do not use the tiny phillips head screwdriver that came with your kit, that's for adjusting the sound sensor and LCD backlight and it's not strong enough. | 1 |
| 23:25, 28 June 2015 | Mimsy-build-fig-08.jpg (file) |  |
1.75 MB | Mimsy Build figure 8. It's easier to insert the 20-tooth gear with servo horn by holding the drive train with the servo on top. Slide the gear/horn in between the plates and using the large pie-shaped holes on the outer plate, position the gear/horn. Y... | 1 |
| 21:57, 28 June 2015 | Mimsy-build-fig-07.jpg (file) |  |
117 KB | Mimsy Build figure 7. Insert the cross shaped servo horn in the matching slot in the 20-tooth gear. Make sure the collar (in the center) is facing up. | 1 |
| 21:40, 28 June 2015 | Mimsy-build-fig-06.jpg (file) |  |
1.02 MB | Mimsy build figure 6. Make sure the servo motor's wire is on the opposite side from the notch in the inner plate. | 1 |
| 13:58, 27 June 2015 | Mimsy-build-fig-04.jpg (file) |  |
468 KB | Place the inner plate on the screws (with the inscribed circles face down toward the gears) and use the nuts to secure. Proper tension on the nuts is important. The gears should be able to spin for a couple of seconds if you flick them with your hand. ... | 1 |
| 13:39, 27 June 2015 | Mimsy-build-fig-03.jpg (file) |  |
712 KB | 1 | |
| 13:30, 27 June 2015 | Mimsy-build-fig-02.jpg (file) |  |
825 KB | Vorpal Mimsy Build Figure 2. Drive train screws placed on outer plate, white spacer and one large spacer placed on each screw. | 1 |
| 13:03, 27 June 2015 | Mimsy-build-fig-01.jpg (file) |  |
735 KB | 2 | |
| 01:16, 26 June 2015 | Parts-cross-bar-wire-guide.jpg (file) |  |
5 KB | Cross bar wire guide. This part slots into the cross bar and provides oval windows you can feed motor and sensor cables through, keeping them better managed. | 1 |
| 01:14, 26 June 2015 | Parts-cross-bar.jpg (file) |  |
5 KB | Cross bar. This part mounts under the drive train servos and helps lock the two drive train halves together securely. It also keeps sensor and motor wires from falling down on top of the battery pack. | 1 |
| 01:13, 26 June 2015 | Parts-console-wire-plate.jpg (file) |  |
3 KB | Console wire plate. This is simply used to hold down the LCD and buzzer cables on the console. | 1 |
| 01:12, 26 June 2015 | Parts-console.jpg (file) |  |
25 KB | Console. Provides bezel for LCD display, also the buzzler, Arduino Nano, and IO shield mount on it. | 1 |
| 01:10, 26 June 2015 | Parts-front-grill.jpg (file) |  |
17 KB | Front grill, used to hide wires. Can be removed without tools to change out batteries. | 1 |
| 00:57, 26 June 2015 | Parts-outer-plate.jpg (file) |  |
29 KB | Mimsy 1.1 Outer Plate rev62 | 1 |
| 02:27, 24 June 2015 | Mimsy-Arduino-Access.jpg (file) |  |
806 KB | 2 | |
| 02:09, 24 June 2015 | Mimsy-annotated.jpg (file) |  |
1.32 MB | Vorpal Mimsy sensors and actuator. | 1 |
| 23:40, 23 June 2015 | MainPage-Mimsy11.jpg (file) |  |
751 KB | 1 | |
| 17:16, 22 June 2015 | Screenshot 20150620-205225 1.png (file) |  |
107 KB | Vorpal Commander Android App with Drawer Open | 1 |
| 17:15, 22 June 2015 | Screenshot 20150620-205243.png (file) |  |
48 KB | Vorpal Commander Android App in DPAD mode on a small screen device | 1 |
| 17:14, 22 June 2015 | Vorpal-commander-tank-drive.jpg (file) |  |
30 KB | Vorpal Commander Android App in Tank Drive Mode | 1 |
| 17:13, 22 June 2015 | Vorpal-commander-arcade.jpg (file) |  |
30 KB | 1 | |
| 17:10, 22 June 2015 | 05-Mimsy-yellow-arm-yellow-sensor-blue-grill.jpg (file) |  |
2.94 MB | Vorpal Mimsy with yellow and blue theme | 1 |
| 16:59, 22 June 2015 | 01-mimsy-all-red-center.jpg (file) |  |
1.5 MB | Vorpal Mimsy 1.1 with all red parts down the center of the robot. | 1 |
