User contributions
From Vorpal Robotics Wiki
(newest | oldest) View (newer 20 | older 20) (20 | 50 | 100 | 250 | 500)
- 17:47, 9 July 2015 (diff | hist) . . (+22) . . N File:Mimsy-build-fig-35.jpg (Mimsy build figure 35.) (current)
- 17:46, 9 July 2015 (diff | hist) . . (+22) . . N File:Mimsy-build-fig-34.jpg (Mimsy build figure 34.) (current)
- 17:44, 9 July 2015 (diff | hist) . . (+22) . . N File:Mimsy-build-fig-33.jpg (Mimsy build figure 33.) (current)
- 17:43, 9 July 2015 (diff | hist) . . (+22) . . N File:Mimsy-build-fig-32.jpg (Mimsy build figure 32.) (current)
- 17:30, 9 July 2015 (diff | hist) . . (+22) . . N File:Mimsy-build-fig-31.jpg (Mimsy build figure 31.) (current)
- 17:25, 9 July 2015 (diff | hist) . . (+22) . . N File:Mimsy-build-fig-30.jpg (Mimsy build figure 30.) (current)
- 14:16, 2 July 2015 (diff | hist) . . (+112) . . Template:MimsySeeAlso (→Extensions, Hacks and Contributions) (current)
- 02:34, 30 June 2015 (diff | hist) . . (+87) . . N File:Mimsy-build-fig-29.jpg (Mimsy Build figure 29. The console fits in the two slots on the rear of Mimsy as shown.) (current)
- 02:29, 30 June 2015 (diff | hist) . . (+122) . . N File:Mimsy-build-fig-28.jpg (Mimsy Build figure 28. Route the cables as shown and use the console wire plate and two 3/8" screws to hold them in place.) (current)
- 02:15, 30 June 2015 (diff | hist) . . (+147) . . N File:Mimsy-build-fig-27.jpg (Mimsy Build figure 27. Install the buzzer using two 3/8" screws, do not overtighten. Connect the LCD cable as shown with the black wire at the top.) (current)
- 02:03, 30 June 2015 (diff | hist) . . (+154) . . N File:Mimsy-build-fig-26.jpg (Mimsy Build figure 26. Attaching the 10cm 3-wire cable to the buzzer. The black wire matches with the "-" marking while the white matches the "S" marking.) (current)
- 03:05, 29 June 2015 (diff | hist) . . (+90) . . N File:Mimsy-build-fig-25.jpg (Mimsy Build figure 25. The LCD is secured with two screws at the top of the console bezel.) (current)
- 02:59, 29 June 2015 (diff | hist) . . (+84) . . N File:Mimsy-build-fig-24.jpg (Mimsy Build figure 24. Remove the protective plastic from the LCD before installing.) (current)
- 02:53, 29 June 2015 (diff | hist) . . (+77) . . N File:Mimsy-build-fig-23.jpg (Mimsy Build figure 23. Installation of Arduino Nano and IO shield on console.) (current)
- 02:42, 29 June 2015 (diff | hist) . . (+62) . . N File:Mimsy-build-fig-22.jpg (Mimsy Build figure 22. Parts needed to assemble control panel.) (current)
- 02:28, 29 June 2015 (diff | hist) . . (+69) . . N File:Mimsy-build-fig-21.jpg (Mimsy Build figure 21. The front floor is shown with fence installed.) (current)
- 02:24, 29 June 2015 (diff | hist) . . (+140) . . N File:Mimsy-build-fig-20.jpg (Mimsy Build figure 20. Installation of battery brackets. Alternate position is for alternative batteries such as 7.2 volt NIMH RC batteries.) (current)
- 02:23, 29 June 2015 (diff | hist) . . (+75) . . N File:Mimsy-build-fig-19.jpg (Mimys Build figure 19. Parts needed to install battery brackets and fences.) (current)
- 01:51, 29 June 2015 (diff | hist) . . (+81) . . N File:Mimsy-build-fig-18.jpg (Mimsy Build figure 18. Front view of chassis with servo wires routed to the rear.) (current)
- 01:44, 29 June 2015 (diff | hist) . . (+144) . . N File:Mimsy-build-fig-17.jpg (Mimsy Build figure 17: using the same locking tab and slot system, take the sensor bar and align and press in first one side and then the other.) (current)